Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Learn fundamentals as you work a given plan through to completion. With a focus on six essential power tools, learn properties of wood and shop etiquette, interpret a plan, cut and mill stock and use basic machine joinery. This class qualifies students for intermediate classes and for Woodworking Open Shop. It is our gateway to more advanced woodworking. Complete attendance is required to fulfill this requirement. See our withdrawal policies online. Limit 8 students

Description: Have you toyed with the idea of building your own cabinets for the kitchen, or the garage? And, as all woodworkers realize, the shop never has enough storage? If this synopsis connects with you, then Woodcraft's new Cabinet Making Series may fill the bill for you. The Cabinet Making Series is designed to maintain continuity by combining all the components of basic cabinetry in 17 hours (three sessions) of classroom and ptractical hands on instruction. Students will learn bisc fundamentals in how to choose and prepare stock to construct Base Units, Upper Wall Units, Drawers and Raised Panel Doors. Stock preparation will be accomplished utilizing the jointer, planer, electric miter saw, tablesaw and router table. Cabinet carcasses will be assembled using standard techniques and face frames will be assembled and attached using the Kreg Pocket Hole System. So, come on out, learn the techniques for making your own cabinets from the planning stage to ta finished product complete with drawers and doors.


Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Description: Without a doubt, the tablesaw is the most important power tool in the shop. Safely ripping stock to width, accurately cutting parts to length, cutting angles, bevels and making tenons and tapers are just a few of the tasks that an accurately set up tablesaw excels at. Understanding how the saw works is one of the goals of this new class and basic common sense safety will be covered thoroughly. We will begin with techniques to make safe and specialized cuts such as making accurate tenons and miters. Saw blade selection, dado blades and some of the commercially available accessories will be discussed. We will also demonstrate some basic but important shop made jigs. While this class will mostly be dom only, students will have the opportunity to do some cutting on the saw in order to make sure that each participant understands the techniques being shown.
$1250.00 (Includes All Materials)          . $300.00 Deposit (Balance due 30 days before class) This six day sculpted chair class will definitely broaden and raise your woodworking skills a few notches. The class will cover topics such as chair joinery, design, placement of back spindle for comfort, defining hard and soft lines, sculpting using various methods such as grinder, rasps, gouges, scrapers and spoke shaves. Cherry wood will be prepared for you before you arrive to save…
Designed for beginners with little to no woodworking experience, this five-session class covers wood physics, shop safety and etiquette, an introduction to joinery concepts, and hands-on experience with the most commonly used woodworking machines. The project for this class is a small side table featuring half-laps, bridle joints, and a round top....

I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
×