$875.00 (Includes all Materials) . $300.00 Deposit (Balance due 30 days before class) Good joinery is key to making fine furniture that will last for generations. Many of us are intimidated by the complexity of these joints. In this class we hope to de-mystify and simplify the joinery process. We will learn western and eastern joinery and their applications, including dovetails, half-blind dovetails, sliding dovetails, mortise-and-tenons, angled mortise-and-tenons, lap joints, bridle joints, miter joints, scarf joints,…
Description: One of the first hand held power tools every novice wood worker should have in their arsenal is the router. With an assortment of sharp cutter bits, the router will become one of the most used small power tools in the shop. Although highly versatile, the router can be very intimidating; due to its size and the speed and torque it develops. In the Router 101 class, students will learn how to choose a router, the types of bases used with the router, and the care and feeding (maintenance) of the router. Students will also learn about the categories of router bits, the components used to identify them, what goes into the making of a router bit, and what to look for in making a choice of which bit best meets their needs. So come on out, bring your router and bits if you have them and learn basic routing techniques and tips and tricks to enhance your routing skills.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
$1555.00 (Includes all Materials) . $500.00 Deposit (Balance due 30 days before class) This is perhaps the most difficult class we offer at our school. This class is not for the faint hearted. This chair will challenge every area of your woodworking skill. We will be dealing with angles, proportion, chair design, choosing wood grain, sculpting of the crest rail using an angle grinder, inlay techniques for the back…
Woodworking classes and seminars from Highland Woodworking. For more than 35 years, we have attracted to Atlanta nationally known woodworking masters and prominent authors including Tage Frid, Sam Maloof, Chris Schwarz, Jeff Miller, Peter Galbert, Roy Underhill and the likes. With the help of numerous other teachers and craftsmen our woodworking programs have inspired and taught thousands of woodworkers to become better at their craft. We consider it great fortune to be in this company and to be able to offer our woodworking classes, seminars and workshops to you. You can check out some of the woodworking action on the Gallery Pages of our site.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.