We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.

I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.


Description: Have you toyed with the idea of building your own cabinets for the kitchen, or the garage? And, as all woodworkers realize, the shop never has enough storage? If this synopsis connects with you, then Woodcraft's new Cabinet Making Series may fill the bill for you. The Cabinet Making Series is designed to maintain continuity by combining all the components of basic cabinetry in 17 hours (three sessions) of classroom and ptractical hands on instruction. Students will learn bisc fundamentals in how to choose and prepare stock to construct Base Units, Upper Wall Units, Drawers and Raised Panel Doors. Stock preparation will be accomplished utilizing the jointer, planer, electric miter saw, tablesaw and router table. Cabinet carcasses will be assembled using standard techniques and face frames will be assembled and attached using the Kreg Pocket Hole System. So, come on out, learn the techniques for making your own cabinets from the planning stage to ta finished product complete with drawers and doors.
Description: Come explore the world of chip carving! Geometric and free form designs created with a cutting knife and stab knife provide tremendous opportunities for artistic expression based on generations of tradition. This hands-on class will cover carving techniques, traditional as well as free form designs, layout and knife sharpening methods. Tools required: Chip carving cutting knife and stab knife, mechanical pencil with .5mm lead, eraser, T-square, and draftsman's compass. Recommended reading: The Complete Guide to Chip Carving by Wayne Barton.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Designed for beginners with little to no woodworking experience, this five-session class covers wood physics, shop safety and etiquette, an introduction to joinery concepts, and hands-on experience with the most commonly used woodworking machines. The project for this class is a small side table featuring half-laps, bridle joints, and a round top....
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.

Looking to jump right into the world of fine woodworking? Is your goal is to continue creating projects long after attending one of our workshops? Then Introduction to Furniture Making is for you! Throughout this 16 hour intensive workshop (split over 4 or 6 sessions), students will build a solid foundation for their new venture into woodworking....


The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
×