Description: The bandsaw is one of your most versatile power tools, and this class will show you how to safely get the most out of it. Steve will show you how to set up your bandsaw for consistent accuracy and teach you proper blade selection. Learn how to perform straight cuts, curves, and how to rough saw cabriole lets. You'll also learn the secrets of resawing: a technique that can save you money and add uniqueness to your projects
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Description: In this workshop, Ray explains the different types and uses of period layout tools. It amazes people to leans how few furniture "Plans" were used in 18th century work. Sketches were made and basic principles were applied to derive at their measurements for quick and efficient use of shop time. Learn what the term "Shop Math" means as Ray demonstrates how to figure out measurements without the use of a rule?
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
Description: Inside out turning, also known as split turned, creates very interesting shapes that leave people wondering how you did that? During this class you will learn the basic concepts on how to design, lay out and turn such a project. This style of turning can be utilized in many projects from vases to ornaments and beyond. Each student will create a decorative flower vase in this class.
Description: In this class period furniture maker Ray Journigan will show you why there were so many different types of planes and what each one was used for. Through demonstrations, he will show you why the most expensive plane is NOT necessary to get a perfect surface. Watch his procedure of making rough lumber turn into glass smooth, finish ready surfaces in just minutes, no sanding necessary! Ever wonder what to look for in a flea marker plane? How to sharpen it for razor thin shavings? How to set it up properly? What makes one plane better than another? Come see why every shop needs a good hand plane no matter what style furniture you make. If you are thinking about incorporating hand tools into your work, take this class before you buy your first hand plane.
I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
With a variety of styles covering every skill-level, the Great Book of Woodworking Projects has something for everyone. Whether you want a challenging project that will beautify your home, such as a stunning Stickley chest of drawers, or you need a quick and easy project for a gift, such as a keepsake box or picture frame, you will find plans that will take a few hours or a weekend to complete.
Description: Learn to make a cutting board with various species of wood. You will prepare, glue, cut on a band saw, rout, and finally apply a food-safe finish. This process will result in a stunning cutting board! You will learn how to use a router and one of our templates to make a fun shape or choose to keep a traditional rectangular shape. Some sanding and finishing will need to be completed at home.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Description: Through relief carving, a common piece of flat wood is transformed into your own woodcarving creation. In this class you will learn basic relief carving techniques such as stop cuts, undercutting, and depth and shadows. The application of the skills is universal and can be used in sign making, decorating furniture, picture frames, standalone creations, and more.
Description: The bandsaw is one of your most versatile power tools, and this class will show you how to safely get the most out of it. Mike will show you how to set up your bandsaw for consistent accuracy and teach you proper blade selection. Learn how to perform straight cuts, curves, and how to rough saw cabriole lets. You'll also learn the secrets of resawing: a technique that can save you money and add uniqueness to your projects
It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.
Description: This is a more in depth class about bench planes than above. In this class, let period furniture maker Ray Journigan show you how to make using a bench plane your new favorite go to tool. Lean what makes one plane better than another? Then Ray demonstrates the steps of flattening a wide board using hand planes followed by each student having the opportunity to surface a board to "finish ready" without any sanding using their hand planes. In this class we take the plane apart and explain all the adjustments to properly tune up your hand plane. Then block planes are discussed showing their importance in furniture work. Next, for those REALLY interested in learning how different types of handplanes were used, Ray will show and demonstrate the use of specialty planes such as Rabbit planes, Shoulder planes, Dado planes, Dovetail planes, Scraper planes, and molding planes. Lastly we turn our attention to sharpening to a razor edge. Student leave with an eye opening experience having learned thru practice, the joy and ease of using hand planes.
Really nice projects but I wish they didn’t use machines every every single step not everyone has a full commercial shop with huge commercial sized machines that cost thousands of dollars in their house. They need to start focusing on hand tools what what the average person has in their house like table saw and drills and stuff like that not everyone has a massive router table with specialty fence and machine or a commercial band saw or massive commercial table saw or huge joiners and thickness planners. It’s not prectical for most people. The steps are short too like Ok do this whole section on this commercial machine that not average woodworker owns and only someone with a commercial company would even have access to but those people aren’t buying this book because they know how to do these things already they don’t need a book telling them how to do what the legit do as a career. The people buying this book are normal people trying to do this as a hobby for fun at home. So cater to them don’t take a short cut because it’s easy for you to tell someone to do something you can do in two seconds but those people have to somehow figure out how to do this one their own in a way not shown in the book because they don’t have the machines you do. It’s Being lazy and writing a book that’s almost completely useless to someone trying to make these projects. But if I did own all these machines and has all that space and money and materials it’s a good book.
Description: In this workshop, Ray shows and demonstrates the tools used to shape different furniture parts used in 18th century work. Tools such as spokeshaves, rasps and files, drawknives, scrapers, beaders and even some homemade tools that Ray uses to replicate period moldings and other features seen in period work. Other topics for shaping furniture parts will also be discussed such as steambending, bent laminations, and of course, carving.
$995.00 (Includes all Materials) . $300.00 Deposit (Balance due 30 days before class) . This Stool was designed by Sam Maloof in 1950's. Sam could often be found sitting on a walnut leather laced stool, talking on the phone in his kitchen. We made several of these stools over the years. Now is your chance to create one of these historic iconic…
A small oak table is a very useful wooden item for every household. You can yourself make a nice, strong and beautiful oak table suitable for any purpose. See the image below. As you can see, it is a small, yet good enough table to be used as a coffee table, lamp stand, breakfast table, etc. You can also find many other design variants on the internet. Choose the one you want for yourself and start making it now.
$1555.00 (Includes all Materials) . $500.00 Deposit (Balance due 30 days before class) This is perhaps the most difficult class we offer at our school. This class is not for the faint hearted. This chair will challenge every area of your woodworking skill. We will be dealing with angles, proportion, chair design, choosing wood grain, sculpting of the crest rail using an angle grinder, inlay techniques for the back…
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.
$1320.00 (Includes all Materials) . $300.00 Deposit (Balance due 30 days before class) This is one of our more popular classes. This beautiful table is well proportioned, with simple elegant lines that will grace any home. It can be used as a hall table, sofa table or an entry table. Imagine what your guest will say when they are welcome into your home and met with this stunning piece of furniture. This class covers all…
This seven-session workshop builds on skills learned during SXW 680 or SXW 686. Students learn additional foundation skills to build wood furniture and related objects incorporating wood physics and joinery concepts. Traditional hand tools including block planes, cabinet scrapers, and spokeshaves are introduced as well as how to safely operate woodworking...
Description: New to the shop environment? Not comfortable around machinery? Spend a day getting to know your way around with one of our experienced instructors. Students will learn the purpose and safe operations of the primary stationary tools such as the tablesaw, jointer, planer, bandsaw and drill press. This hands on class will give you a taste of how these tools take raw material and turn it into finished projects. To the beginner woodworker, this class will pave the way for participation in Woodworking Fundamentals 1.
Description: A sharp tool is a turner's best friend. If you are having difficulty achieving smooth cuts and relying on scraping rather than cutting then this is the class for you. In this class you will learn a quick and easy way to repeatedly and consistently sharpen all of your wood turning tools using the Wolverine sharpening system on a slow speed grinder. The Varigrind jig will be demystified and you will be show a simple method to sharpen all of your bowl and spindle gouges. Sharpening the spindle roughing gouge, skew, and scraper will also be discussed and demonstrated. Bring your turning tools - as many as you want to sharpen to practice your skills in class.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.