Designed for beginners with little to no woodworking experience, this five-session class covers wood physics, shop safety and etiquette, an introduction to joinery concepts, and hands-on experience with the most commonly used woodworking machines. The project for this class is a small side table featuring half-laps, bridle joints, and a round top....

Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.


A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.


Description: This is a more in depth class about bench planes than above. In this class, let period furniture maker Ray Journigan show you how to make using a bench plane your new favorite go to tool. Lean what makes one plane better than another? Then Ray demonstrates the steps of flattening a wide board using hand planes followed by each student having the opportunity to surface a board to "finish ready" without any sanding using their hand planes. In this class we take the plane apart and explain all the adjustments to properly tune up your hand plane. Then block planes are discussed showing their importance in furniture work. Next, for those REALLY interested in learning how different types of handplanes were used, Ray will show and demonstrate the use of specialty planes such as Rabbit planes, Shoulder planes, Dado planes, Dovetail planes, Scraper planes, and molding planes. Lastly we turn our attention to sharpening to a razor edge. Student leave with an eye opening experience having learned thru practice, the joy and ease of using hand planes.
Description: Without a doubt, the tablesaw is the most important power tool in the shop. Safely ripping stock to width, accurately cutting parts to length, cutting angles, bevels and making tenons and tapers are just a few of the tasks that an accurately set up tablesaw excels at. Understanding how the saw works is one of the goals of this new class and basic common sense safety will be covered thoroughly. We will begin with techniques to make safe and specialized cuts such as making accurate tenons and miters. Saw blade selection, dado blades and some of the commercially available accessories will be discussed. We will also demonstrate some basic but important shop made jigs. While this class will mostly be dom only, students will have the opportunity to do some cutting on the saw in order to make sure that each participant understands the techniques being shown.
Have you got an old whiskey barrel at home that you haven’t used for ages? If yes, this project is for you. You can make a really beautiful coffee table from that old whiskey barrel in a few easy steps. Apart from a coffee table, whiskey barrels can also be used to build several other furniture items. But that is a talk for later. Here, we will discuss how to make a coffee table from a whiskey barrel.
Cerritos College Woodworking, one of the finest woodworking schools in Southern California, offers classes in furniture making, cabinetmaking, CNC woodworking, and related topics.  Cerritos is the school for you, whether your goal is to acquire new knowledge, gain confidence in or improve your skills, enter the field of professional woodworking, or develop a rewarding hobby.
Description: The bandsaw is one of your most versatile power tools, and this class will show you how to safely get the most out of it. Steve will show you how to set up your bandsaw for consistent accuracy and teach you proper blade selection. Learn how to perform straight cuts, curves, and how to rough saw cabriole lets. You'll also learn the secrets of resawing: a technique that can save you money and add uniqueness to your projects
Description: Come explore the world of chip carving! Geometric and free form designs created with a cutting knife and stab knife provide tremendous opportunities for artistic expression based on generations of tradition. This hands-on class will cover carving techniques, traditional as well as free form designs, layout and knife sharpening methods. Tools required: Chip carving cutting knife and stab knife, mechanical pencil with .5mm lead, eraser, T-square, and draftsman's compass. Recommended reading: The Complete Guide to Chip Carving by Wayne Barton.
Description: Without a doubt, the tablesaw is the most important power tool in the shop. Safely ripping stock to width, accurately cutting parts to length, cutting angles, bevels and making tenons and tapers are just a few of the tasks that an accurately set up tablesaw excels at. Understanding how the saw works is one of the goals of this new class and basic common sense safety will be covered thoroughly. We will begin with techniques to make safe and specialized cuts such as making accurate tenons and miters. Saw blade selection, dado blades and some of the commercially available accessories will be discussed. We will also demonstrate some basic but important shop made jigs. While this class will mostly be dom only, students will have the opportunity to do some cutting on the saw in order to make sure that each participant understands the techniques being shown.
$375.00 (Includes all Materials)          . $100.00 Deposit  (Balance due 30 days before class) This class will give every student a thorough understanding of the finishing process. It will cover all aspects of wood finishing: Proper sanding techniques, coloring wood (dyes, stains, chemical and plant dyes), color-matching, membrane finishes (shellac, varnish, lacquer) and understanding solvents and their use in the finishing process. We will also explore hand-rubbed finishes, shading and toning, making your own custom stains and…
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
$360.00 (Includes all Materials)               . $100 Deposit (Balance due 30 days before class) There is nothing like the experience of using sharp tools. Where the actual tool does what you want it to do with ease. You should not have to fight with your tools. They should work for you and with you. In this class, we will cover a variety of techniques for sharpening edge tools including the use of Japanese water stones.…

The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.


As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
Description: Spend a weekend with Woodcraft and leave with a traditional Adirondack chair. This course is designed for the entry to intermediate level woodworker who would like to improve their furniture building skills. You will work with both power and hand tools to cut, drill, sand and assemble this classic chair. Instructions, drawings, cypress wood and fasteners are included in the tuition.
Description: Do you and your significant other want to le3arn basic wood working skills and have fun creating a one of a kind project together? We will provide the food, soft drinks, and materials. You only need to show up and be ready to make some saw dust. Projects will vary from month to month and will consist of small projects such as pens, bottle stoppers/openers, pepper grinders, etc.
$1250.00 (Includes all Materials)            . $300.00 Deposit (Balance due 30 days before class) In this class not only will we build this beautiful coffee table inspired by Greene and Greene, Stickley and a little bit of Krenov, but we will learn many table construction techniques. Reading wood grain, Mortise & tenon, shaping wood, bread board ends, drawer construction, fitting the drawer, as well as many of the Greene and Greene details such as square ebony…
Description: Painted furniture is all the rave today. Using Black Dog Furniture Paint, come learn how to transform those yard sale finds, thrift store picks or your grandmother's hand me downs into unique beautiful treasures for your home. Bring a small piece of furniture (chair, small side table etc.) that is good condition (no major repairs etc.) and we will provide the rest of supplies needed to transform your trash to treasure. Student can email a photo of furniture to instructor prior to class to make sure that it is suitable piece to paint). In this class you will learn the basics of prepping, painting, distressing, waxing and sealing.

Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.

×